The change has been coming since 2024, when work health and safety ministers agreed to replace the Workplace exposure standards for airborne contaminants (the WES list) with Workplace exposure limits for airborne contaminants (the WEL list). Both lists are published by Safe Work Australia, the national body that writes the model work health and safety laws. The final federal step landed on 20 November, when the Work Health and Safety Amendment (Workplace Exposure Limits) Regulations 2026 were registered. They commence on 1 December 2026 and, for the Commonwealth’s own jurisdiction, write the November 2025 edition of the WEL list into the regulations. The explanatory statement puts the effect plainly: from 1 December 2026, duty holders will be required to comply with the exposure limits set out in the WEL List rather than the exposure standards in the old list.

The duty itself does not change. A business must still make sure nobody at the workplace breathes a contaminant above its limit, and must eliminate or minimise the risk so far as is reasonably practicable. The statement says The Amendment Regulations are not changing the nature of these obligations. What changes is the number. Against the list that applies today, the WEL list introduces exposure limits for 31 airborne contaminants, decreases exposure limits for 186 airborne contaminants and increases exposure limits for 16 airborne contaminants.

The print solvents, old and new

We read both lists for the solvents and cleaners that turn up in offset, flexo, gravure, screen and digital work. TWA is the average over an eight-hour day; STEL is the average over any 15 minutes. A dash means the list gives no figure of that kind. Ethanol’s new row is shown as printed.A

Exhibit A · from the source

Safe Work Australia WEL list, ethyl alcohol row: Ethanol, 64-17-5, TWA 200 ppm, 380 mg/m3, STEL 800 ppm, 1500 mg/m3, OTO
Workplace exposure limits for airborne contaminants, amended November 2025, page 24. Columns, left to right: name, synonym, CAS number, TWA (ppm, then mg/m³), STEL (ppm, then mg/m³), peak limit, advisory notation. The current list (page 23) gives ethanol a TWA of 1000 ppm and no STEL. Open the PDF Back to the story
Eight-hour (TWA) and 15-minute (STEL) limits, ppm unless shown
SubstanceTWA nowTWA from 1 DecSTEL nowSTEL from 1 DecChange in the TWA
Ethanol (ethyl alcohol)1000200-800Down 80%
Isopropyl alcohol400200500400Halved
Toluene5020150-Down 60%; STEL dropped
Acetone5002501000500Halved
n-Butyl acetate (now grouped with its isomers)15050200100Down two-thirds
n-Propyl acetate (now “all isomers”)200100250150Halved
Cyclohexanone2510-20Down 60%
Diacetone alcohol5020--Down 60%
2-Butoxyethanol (butyl glycol)20105040Halved
Styrene monomer502010040Down 60% (Victoria: see below)
Mineral turpentine (mg/m³)480296-593Down 38%
White spirits (mg/m³)790296-593Down 63%
Methyl ethyl ketone (MEK)150200300300Up a third
n-Hexane2050--Up 150%
Ethyl acetate200200400400No change
n-Propyl alcohol200200250250No change
Propylene glycol monomethyl ether (PM)100100150150No change
PM acetate (1-methoxy-2-propanol acetate)5050100100No change
n-Heptane400400500500No change
Xylene8080150150No change
“Now”: Safe Work Australia, Workplace exposure standards for airborne contaminants, amended November 2025. “From 1 Dec”: Workplace exposure limits for airborne contaminants, amended November 2025, the edition the Commonwealth regulations adopt. The November 2026 edition carries the same figures for every row here. Percentages are our arithmetic on the TWA column, for example ethanol (1000 − 200) ÷ 1000 = 80%, toluene (50 − 20) ÷ 50 = 60%, white spirits (790 − 296) ÷ 790 = 62.5%, mineral turpentine (480 − 296) ÷ 480 = 38.3%, MEK (200 − 150) ÷ 150 = 33%. Page numbers are in the sources list.

Two other changes ride along with the numbers. The new list marks some substances OTO, meaning Exposure can increase the risk of hearing loss. Among the rows above, eight carry it: ethanol, toluene, xylene, styrene, n-hexane, n-heptane, mineral turpentine and white spirits. The list adds: Hearing loss is more likely to occur if a worker is exposed to both noise and ototoxic substances than if exposed to just noise or the ototoxic substance alone. And the old “Sen” flag for sensitisers is split into skin (DSEN) and breathing (RSEN), which matters for isocyanate laminating adhesives and some UV chemistry. The isocyanate group limit itself, 0.02 mg/m³ over eight hours, is the same on both lists.

What is not changing on 1 December

Nine chemicals were pulled out of the main review for further impact analysis, and they keep their old figures for now. WorkSafe Victoria, the state’s regulator, lists them as benzene, chlorine, copper, formaldehyde, hydrogen cyanide, hydrogen sulphide, nitrogen dioxide, respirable crystalline silica and titanium dioxide, and says the current limits will continue to apply to all nine chemicals that were separately assessed during the national review. Titanium dioxide, the usual white pigment in inks and coatings, is in that group. Benzene has a decision, a lower limit of 0.2 ppm from 1 June 2027; the other eight are still with an expert panel.

Victoria, which has its own occupational health and safety law rather than the model laws, adopts the WEL list on the same day but with a longer run for some substances: In Victoria, transition arrangements apply to 15 substances until 1 December 2029. Styrene monomer is one of the 15, so a Victorian screen or composites shop has until then on styrene. None of the other solvents in our table is on Victoria’s list.

Every other state and territory makes the change through its own regulations. Safe Work Australia’s announcement says the WEL list applies from 1 December 2026 following implementation into the WHS laws of the Commonwealth, states and territories. We have read the Commonwealth regulations and Victoria’s position; we have not read each other state’s instrument, so check your own regulator for any substance-by-substance variation.

Our view, labelled as such

For most print businesses this is a paperwork change with two exceptions worth real attention. The first is ethanol. A limit that drops from 1000 to 200 ppm means an air test that came back at, say, a third of the old limit is now above the new one. If your solvent-based flexo or gravure inks, or your wash-up, run on ethanol, any monitoring done against the old list is no longer evidence that you comply. The second is isopropyl alcohol: if your dampening system uses it, its limit has halved, and so has your margin. Toluene, where it is still used, now has a limit two-fifths of the old one and no 15-minute figure at all.

The sensible first step costs nothing. Pull the safety data sheet for every ink, wash, cleaner and adhesive on the floor, note which of the substances in our table it contains, and compare against the new column, not the figure printed on the sheet, which may have been written against the old list. Where a cut is large and you have no recent monitoring, that is where to spend on an occupational hygienist first. And where a press hall is loud, the OTO flag is a reason to look at noise and solvent exposure together rather than as two separate checklists. WorkSafe Victoria’s line applies everywhere: Exposure limits are not a target. This is our reading of the published limits, not advice from any regulator.

How we sourced this

The commencement date, the adoption of the November 2025 WEL list and the counts of new, reduced and increased limits come from the Work Health and Safety Amendment (Workplace Exposure Limits) Regulations 2026 (Federal Register F2026L01508, registered 20 November 2026) and its explanatory statement, pages 1 to 3. The table figures come from Safe Work Australia’s two list PDFs, both amended November 2025, read row by row from the Word versions and checked against the PDFs; we also compared the November 2026 WEL edition, whose only recorded amendment updates references to guidance. Exhibit A is cut from page 24 of the WEL PDF. The OTO and sensitisation notes come from the WEL list’s notation table and Safe Work Australia’s page on changes between the lists. The nine held-back chemicals, the benzene decision and the Victorian transition come from WorkSafe Victoria’s frequently asked questions, read 21 November 2026.

What we have not done. We have not read the WHS regulations of New South Wales, Queensland, South Australia, Western Australia, Tasmania, the ACT or the Northern Territory, so we do not say each has adopted the list unchanged on 1 December. We did not contact Safe Work Australia or any regulator; nothing in this piece rests on an answer from them. The table covers 20 substances we chose as common in print, not the whole list. Safe Work Australia and WorkSafe Victoria are not clients or advertisers on this masthead.

Sources

How we put this together. AI systems researched and wrote it under our standing editorial rules, taking its facts from the primary sources below. 11 quotes were matched by software, word for word, against saved copies of the sources. How The Print Register works.

  1. Commonwealth of Australia, Work Health and Safety Amendment (Workplace Exposure Limits) Regulations 2026 (F2026L01508, made 12 November 2026, registered 20 November 2026, read 21 November 2026): commencement on 1 December 2026 (section 2, page 1) and the new definition of exposure limit (Schedule 1, item 1, page 2).
  2. Minister for Employment and Workplace Relations, Explanatory statement to F2026L01508 (registered 20 November 2026, read 21 November 2026): the effect from 1 December (page 1), the unchanged obligations and the counts of new, reduced and increased limits (pages 2 to 3), and the fixed November 2025 edition (page 3).
  3. Safe Work Australia, Workplace exposure limits for airborne contaminants, amended November 2025 (PDF, read 21 November 2026): the OTO notation and its wording (notation table), and the new figures for acetone (page 12), 2-butoxyethanol and butyl acetate (15), cyclohexanone (19), diacetone alcohol (20), ethanol and ethyl acetate (24), n-hexane (27), isopropyl alcohol (29), MEK (31), mineral spirits (34), propyl acetate and propyl alcohol (39), styrene (42) and toluene (45). The ethanol row is shown in Exhibit A.
  4. Safe Work Australia, Workplace exposure standards for airborne contaminants, amended November 2025 (PDF, read 21 November 2026): the current figures for acetone (page 13), 2-butoxyethanol and n-butyl acetate (15), cyclohexanone (19), diacetone alcohol (20), ethanol and ethyl acetate (23), n-hexane (25), isopropyl alcohol (26), MEK (29), mineral turpentine (30), n-propyl acetate and propyl alcohol (34), styrene (37), toluene (39) and white spirits (40).
  5. Safe Work Australia, Workplace exposure limits for airborne contaminants (document page, last updated 5 November 2026, read 21 November 2026): the November 2026 edition and its amendment record, compared against the November 2025 figures.
  6. Safe Work Australia, Changes between the WES and WEL (web page, read 21 November 2026): the split of the sensitisation notation and the new OTO notation.
  7. Safe Work Australia, New Workplace exposure limits (WEL) to apply from 1 December 2026 (news item, read 21 November 2026): adoption following implementation in each jurisdiction’s laws.
  8. WorkSafe Victoria, Workplace exposure limits: frequently asked questions (web page, read 21 November 2026): the nine separately assessed chemicals, the benzene decision, the 15 Victorian transition substances including styrene monomer, and the quoted lines.

Run a pressroom and had air monitoring done against the new limits, or found a solvent we should have listed? Tell us and we will check it against the sources and log the outcome here.